Categories: Electronics Hardware
Tags: ps3 repair teardown video game
Posted by: Darian Cabot
Comments:11
Repair: Replacing a dead PS3 Dualshock 3 controller battery
I’m sick of seeing this notification! I’ll usually only get 20 minutes play time before the controller requires charging again. I’ve had it on charge for weeks, since the last time I used the PS3. I don’t use the PS3 often, and I’m holding out for Uncharted 4 next year before I consider buying a PS4 😛 Anyway the controller’s internal battery is beyond it’s number of recharge cycles and in need of replacement. Here’s how I did it…
Luckily there’s just 5 phillips-head screws and no security screws, a rarity for consumer electronics these days. After removing the screws on the back of the controller, hold it face down and carefully remove the back half. You’ll see the Li-ion battery pack in it’s cradle as pictured.
You can see on the left it’s connected to the PCB with a standard 2-pin JST connector. Carefully disconnect this by prying/wiggling it off with a flat-head screwdriver, and it’s ready for a replacement battery. Simple! 🙂
There is a label on the battery pack with all the relevant details. It’s a model LIP1359 – which as far as I can tell is a custom battery by Sony used in the PS3 Dualshock 3 controllers only. It’s a 3.7V 610mAh Li-ion battery.
Li-ion battery teardown
I couldn’t help doing a quick teardown on the battery pack. It’s obviously a standard Li-ion flat pack as found in mobile phones, but I was curious to see if there was any protection circuitry inside. The plastic shell was quite difficult to separate so I think it’s been ultrasonically welded. I had to be careful because damaging a li-ion cell can cause a fire.
Here are a few photos of the LIP1359 teardown (close shots were taken using my Andonstar microscope):
Immediately the suspected protection circuit was found (the skinny white PCB). On the flip-side there are a few SMT components. IC01 is marked “AD 1B7”. I was unable to find data sheets for any of these parts, but I think this is a Li-ion protection IC. Q01 is marked “201” and I’m assuming this is a MOSFET or similar used by IC01 to disconnect the battery for protection. Usually integrated Li-ion protection is to mitigate short-circuit and under voltage conditions.
If I was feeling particularly keen and wanted to save a buck, I could use the identifying marks on the Li-ion cell to replace only that and reuse the protection circuit and housing. I’m too lazy for that (and I destroyed the housing), but Googling US323450 returns a bunch of suppliers, Sony MSDS documentation, etc.
Time to find a new battery pack and swap it out…
Finding a replacement battery
There are a number of replacement batteries available online. But, as always, one must be careful buying li-ion batteries online! The capacity ratings are often greatly overstated, and you end up paying for a battery that won’t last nearly as long as the genuine one being replaced. All that in consideration, I ended up chosing this item on eBay. It’s in the US, and due to a weak Aussie dollar it’s costing me about $26. Not great, but other options aren’t much cheaper and this seller has decent feedback and shipping times.
Edit: Since posting this blog I found this item on Deal Extreme that would’ve been much cheaper, however shipping is typically much slower too.
Here’s the label on the replacement eBay battery. It’s a direct swap, so all I had to do was plug it back in to the controllers PCB and replace the 5 screws. Sorted!
Hardware and software engineer with experience in product development and building automation. Director at Cabot Technologies and Product Manager at NEX Data Management Systems.
11 comments
Good post.
I am a little suspicious that the battery you pulled out of your controller is not actually a real Sony factory-installed battery but a high-quality clone. It does have the chip (thanks for the teardown), but the rating is 610mAh, not 570mAh as the LIP1359 is supposed to be rated for. There are two other tells that I’ll mention in a bit.
To other readers–be really careful about the battery you buy. There are an awful lot of fakes out there. Avoid anything that has a rating higher than 610mAh (some claim a whopping 1800mAh, which would not be physically possible in a battery of this size).
I have noticed that the genuine Sony Corporation LIP1359 batteries that are in my SIXAXIS controllers do not have their specs printed on a sticker. Instead, the label is injection-molded plastic, all the specs are in raised plastic letters, and the rating is always 570mAh. I also have an older SIXAXIS controller that has the non-chipped NEC TOKIN Corp. MK11-2902 battery. That one IS rated for 610mAh and appears to be the genuine factory-installed model. It also requires the plastic caddy to hold it still within the controller.
Also, all the genuine batteries I have seen have a sticker on the back with a round recycle icon saying “RECYCLE 1.800.822.8837”
Hope this helps other buyers avoid short-lived replacements.
Thanks for the detailed information 🙂
I’d be surprised if it were fake though. I originally purchased my PS3 new in Japan from a large electronics retailer, I’m not sure if this is the controller that came with the PS3, or one that I bought separately in Australia. Either way it was from a popular retail store and new in retail Sony packaging.
I am curious, is the LIP1359 interchangeable with LIP1859? My controllers are using LIP1359, but I could only obtain LIP1859 batteries.
I believe they are the same size, so you should have no trouble installing it. Just be wary of higher capacity batteries, that may be fake (i.e. not really that much capacity) – see the previous comment by dchang0.
Hi.
After three years you posted. What you can say about that replacment batery. Is it still working.
Thanks
Two years…
Truth is I haven’t used the PS3 for a while now. But it was working when I last used it a year or so ago.
Hello,
I just bought a second hand ps3 with two controllers. A dualshock3 (that’s working fine and vibrating) and sixaxis that doesn’t work unless plugged to the console with a mini usb cable.
I opened the sixaxis, its battery appears to be alittle swollen
The thing is i don’t find spare batteries for online (i’m in france) Model MK11-2902
Do you think a battery for a different revision of the ps3 controller will fit ?
A LIP1359 for example
Thanks
My understanding is that a LIP1359 battery is a compatible replacement for LIP1859, MK11-2902, or MK11-3023.
I think that will be fine, but you may want to research this further to be sure.
Hi, you did a good article. I wanted to make you aware that I have found a very economical solution for battery replacement regarding the PS3 joypad battery. Basically two small batteries can be used for the 3.7 volt 380 mAh DZ09 SmartWatches and are put in parallel with each other. You get a 3.7 volt and 760 mAh battery. You can find these low-priced batteries everywhere. Just knowing how to do some welding is done. Greetings Mauro
I purchased my PS3 when they first became available and two dual shock, Sony brand controllers came with it. I just pulled the battery to put in a replacement. The original Sony battery is 1 3/4″ long and the replacement is too big to fit in the ‘cradle’. The new LIP1359 is 2 1/4″ long and slightly wider. My original battery is an MK11-2902, and it says 610mAh on one side and a label on the other side that says: Recycle 1-800-822-8837, Sale by: Sony Corporation, Sony computer entertainment, inc.